Training Courses

Human Factors
Human Factors and Error Management
Human Factors for Managers
Human Factors for Maintainers
Industry Introduction & Familiarisation
Nadcap Special Processes
Anodizing – Process Operator
Anodizing – Process Owner
Anodizing – Process Planner
AS/ EN/ JISQ 9100 Rev C
Contract Review
Fusion Welding (GTAW) – Process Owner
Fusion Welding (GTAW) – Process Planner
Heat Treating – Process Owner
Heat Treating – Process Planner
Internal Auditing
Introduction to Aerospace Quality
Introduction to Pyrometry
Nadcap Audit Preparation – Chemical Processing
Nadcap Checklist Review – Chemical Processing
Nadcap Audit Preparation – Coatings
Nadcap Checklist Review – Coatings
Nadcap Checklist Review – Electronics *new*
Nadcap Audit Preparation – Heat Treating
Nadcap Checklist Review – Heat Treating
Nadcap Audit Preparation – NDT
Nadcap Checklist Review – NDT
Nadcap Audit Preparation – Welding
Nadcap Checklist Review – Welding
NDT Level III Responsibilities
Process Failure Mode and Effect Analysis
Problem Solving Tools
Root Cause Corrective Action (RCCA)
Statistical Process Control
Contract Review (webinar) *new*
RCCA Nadcap Style (webinar) *new*
Safety
Effective Event Investigation Training
Improving Aviation Audit Techniques
Logistics Awareness Cours
SAQG INITIATIVE

Featured Courses

EASA Part 21 Subpart J Design Organisation Approval

Date(s): 21 & 22 November 2019
Annexed to Commission Regulation (EU) No 748/2012 is Annex I (Part 21). EASA Part 21 Subpart J details the elements required of a design organisation in order to hold an EASA Design Organisation Approval (DOA). EASA grants privileges for the DOA to design new products, product modifications or repairs and may include approval for these designs.

Nadcap Checklist Review – Coatings

Date(s): To be advised
This course is designed to provide a complete overview of Nadcap requirements related to the Coatings audit and is presented by experienced Instructors, experts in Nadcap Coatings requirements.

AS 9110C / EN 9110:2016 Internal Auditor Course

Date(s): 14 & 15 May 2020 / 19 & 20 November 2020
AS 9110 Rev C is an Aerospace Standard based on the ISO 9001 Quality Management System (QMS) requirements supplemented with additional quality system requirements established by the aerospace Maintenance, Repair & Overhaul (MRO) industry.

AS 9110C / EN 9110:2016 Foundation Course

Date(s): 11 & 12 May 2020 / 16 & 17 November 2020
AS 9110 Rev C is an Aerospace Standard based on the ISO 9001 Quality Management System (QMS) requirements supplemented with additional quality system requirements established by the aerospace Maintenance, Repair & Overhaul (MRO) industry.

EASA Part 21 Initial Airworthiness

Date(s): 29 & 30 April 2020 / 29 & 30 October 2020
This two-day course will discuss in general terms the legal and regulatory system, as defined through (EC) 2018/1139, and in detail (EU) 748/2012.

EASA CS-25 Cabin Safety Design & Certification

Date(s): 14 to 17 July 2020
This four-day course will equip the delegates with the capability to classify changes to cabin interiors into minor, major or significant, identify applicable CS-25 paragraphs and have the basic knowledge of the Means of Compliance related to the certification process and requirements.

An Introduction to Aerospace MRO Industry

Date(s): 25 & 26 November 2019 *revised dates* / 6 & 7 April 2020
This course provides an overview to the Aerospace Maintenance, Repair and Overhaul (MRO) industry

SAQG Initiative: Aerospace Quality Manager Workshop

Date(s): 16 and 20 December 2019
The workshop is a refreshment training meant for Quality Managers in the aerospace industry. It aims to benchmark the best practices in the quality management system (QMS) used by each organisation.